BootROM - 2.03
Starting CP-1 IOROM 1.07
Booting from SPI NOR flash 1 (0x32)
Found valid image at boot postion 0x000
lNOTICE: Starting binary extension
NOTICE: SVC: SW Revision 0x0. SVC is not supported
mv_ddr: mv_ddr-devel-17.10.1-g??? (Oct 15 2017 - 13:40:06)
warning: mv_ddr4_dq_vref_calibration: subphy 6 vref tap 55 voltage noise
mv_ddr: completed successfully
NOTICE: Cold boot
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.3(release):armada-17.10.3:4af6d73
NOTICE: BL1: Built : 13:40:06, Oct 15 2017
NOTICE: BL1: Booting BL2
lNOTICE: BL2: v1.3(release):armada-17.10.3:4af6d73
NOTICE: BL2: Built : 13:40:06, Oct 15 2017
NOTICE: BL1: Booting BL31
lNOTICE: MSS PM is not supported in this build
NOTICE: BL31: v1.3(release):armada-17.10.3:4af6d73
NOTICE: BL31: Built : 13:40:07, Oct 15 2017
l
U-Boot 2017.03-armada-17.10.1 (Oct 15 2017 - 14:03:12 +0300)
Model: MACCHIATOBin-8040
Clock: CPU 1600 [MHz]
DDR 1050 [MHz]
FABRIC 1050 [MHz]
MSS 200 [MHz]
DRAM: 16 GiB
U-Boot DT blob at : 000000007f70fc38
EEPROM configuration pattern not detected.
Comphy chip #0:
Comphy-0: PEX0
Comphy-1: PEX0
Comphy-2: PEX0
Comphy-3: PEX0
Comphy-4: SFI
Comphy-5: SATA1
Comphy chip #1:
Comphy-0: SGMII1 1.25 Gbps
Comphy-1: SATA0
Comphy-2: USB3_HOST0
Comphy-3: SATA1
Comphy-4: SFI
Comphy-5: SGMII2 3.125 Gbps
UTMI PHY 0 initialized to USB Host0
SATA link 0 timeout.
SATA link 1 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
SATA link 0 timeout.
SATA link 1 timeout.
AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
flags: 64bit ncq led only pmp fbss pio slum part sxs
PCIE-0: Link down
MMC: sdhci@6e0000: 0, sdhci@780000: 1
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
*** Warning - bad CRC, using default environment
Net: eth0: mvpp2-0 [PRIME]mdio_register: non unique device name 'ethernet@0'
, eth1: mvpp2-3, eth2: mvpp2-4, eth3: mvpp2-5
Hit any key to stop autoboot: 0
Card did not respond to voltage select!
mmc_init: -95, time 43
** Bad device mmc 1 **
Card did not respond to voltage select!
mmc_init: -95, time 26
** Bad device mmc 1 **
** First descriptor is NOT a primary desc on 0:1 **
** No partition table - mmc 0 **
** No partition table - mmc 0 **
starting USB...
USB0: Register 2000120 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
*** ERROR: `serverip' not set
*** ERROR: `serverip' not set
Bad Linux ARM64 Image magic!